Gå vidare till produktinformation
1 av 6

G2UT 48 V controller for KuKirin G2 Ultra (2025)

Butiksinformation
Besiktning/hämtning på plats är möjlig måndag till lördag.
Öppettider: Mån–fre: 09:00–19:00
Lör: 10:00–16:00
Sön & helgdagar: STÄNGT
Telefon: +386 30 771 787
Upp till 30 EUR rabattSlutsåld
Ordinarie pris 169,90 EUR
Försäljningspris 169,90 EUR Ordinarie pris 199,90 EUR
Beräknar fraktkostnad…

Fraktkostnaden kan variera beroende på land.

Beräknad leveranstid · Liechtenstein

Kontakta oss för att bekräfta leverans till Liechtenstein.


Betalningsmetoder
  • American Express
  • Apple Pay
  • Bancontact
  • Google Pay
  • iDEAL Wero
  • Klarna
  • Maestro
  • Mastercard
  • MobilePay
  • PayPal
  • Shop Pay
  • Union Pay
  • Visa
Tyvärr är den här produkten slut i lager.

Men vi kan meddela dig så snart den finns tillgänglig igen.

The G2UT controller for the 2025 KuKirin G2 Ultra has separate front and rear motor connections in a single assembly. The black connector housing carries three screw-type phase terminals for each motor and shared +/− battery terminals. A ribbed aluminium base dissipates heat and includes a mounting tab.

Compatibility

For the 2025 KuKirin G2 Ultra with matching G2UT electronics. Compare the controller designation, 48 V rating, complete connector layout, software revision and mounting before ordering. Production batches can use different electronics; fitment for the KuKirin G2, G2 Max or G2 Master is unconfirmed.

Technical specifications

Model and version KuKirin G2 Ultra, 2025
Controller designation G2UT
Rated voltage on label 48 V
Current limit on label 25 ± 1 A; the label does not specify the current for each motor
Motor connections Separate Front and Rear groups; 3 Blue/Green/Yellow screw-type phase terminals each
Power connections + and − screw terminals
Signal connections Front Hall, Rear Hall, 8 Pin, Tail Light and Motor line; compare layout with the photos
Approximate overall dimensions including tab 151.6 × 142.5 × 50.5 mm
Housing height excluding tab approximately 130.6 mm
Mounting slot shown approximately 6.5 × 8.5 mm
Net weight shown in supplier photo approximately 677 g
Versions on the photographed label Firmware JBWC6P V1.4; software RND4825-V1.10

Package contents

1 G2UT controller in its housing and 3 protective covers for the power terminals. A separate wiring harness, battery and display are not included.

Installation and checks

  • Switch off the scooter and disconnect the battery. Photograph all connections and check the front and rear motor labels.
  • Preserve power polarity, phase and Hall wiring assignments, and the intended mounting of the heat sink. Fit the protective covers and restore the deck cover seal.
  • Check both motors, the display and motor cut-off when braking after replacement. Do not change current settings based on this label; electrical compatibility and operation should be checked by a qualified technician.

Reservdelar för KuKirin

EVOLT showroom and service entrances

Varför välja EVOLT?

Tržaška cesta 222, 1000 Ljubljana, Slovenien

Besök vår 200 m² stora utställningslokal i Vič, Ljubljana, där försäljning, service och reservdelar är samlade under ett tak.

Se och prova produkter personligen, med expertvägledning, service i Slovenien och reservdelshjälp efter ditt köp.

MÅN–FRE: 9:00–19:00
LÖR: 10:00–16:00

Spare parts in the EVOLT showroom

Reservdelar och tillbehör

I lager i Ljubljana

EVOLT tillhandahåller reservdelar till elsparkcyklar, elcyklar och andra elfordon.

Utforska komponenter i lager i Slovenien, med leveransberäkningar baserade på produkt och destination.

Vi stöder förare, reparationscenter, återförsäljare och affärspartners genom detalj- och grossistförsäljning.

Fler frågor om G2UT 48 V controller for KuKirin G2 Ultra (2025)?